Sharp Edges

Sharp Edges Mobile, drop off, & mail-in shear, clipper blade & knife sharpening. Serving central Oklahoma & surrounding areas. Call 405-535-7153
(1)

Follow this 5 steps if you feel a snag in your thinner1. Check for a Nick – If the shears catch, there's likely a nick i...
03/17/2025

Follow this 5 steps if you feel a snag in your thinner

1. Check for a Nick – If the shears catch, there's likely a nick in the solid blade. Slowly open and close them to feel where the catch is.

2. Spread & Close – Using your forefinger and thumb, gently spread the blades, then close past the nick.

3. Pinch & Open – Pinch at the nick, then slowly open the shears.

4. Repeat – Do this 3-4 times to smooth out the catch.

5. Test – If the shears still catch, secure them with a rubber band and set them aside for sharpening.

Wait a few more days ❌️Call Jessie at 405-535-7153✅️Or visit: sharpedgesok.com
03/12/2025

Wait a few more days ❌️
Call Jessie at 405-535-7153✅️

Or visit: sharpedgesok.com

For all your sharpening needs...Call: 405-535-7153Visit: sharpedgesok.com
03/07/2025

For all your sharpening needs...

Call: 405-535-7153
Visit: sharpedgesok.com

03/07/2025

If you've tried aligning your clipper blades before but couldn't do it right, watch this video...

🔥Introducing the Lister Star Large Animal Clipper 🔥The all-in-one farm clipper you’ll ever need.• Equipped with a Lister...
02/26/2025

🔥Introducing the Lister Star Large Animal Clipper 🔥

The all-in-one farm clipper you’ll ever need.

• Equipped with a Lister A2F/AC Fine blade, which has a clipping surface width of 3 inches for quick clipping and has a cut length of 1.4 mm (3/64”).

• 16-foot reach + quick-clean filter + self-cooling head = ZERO downtime when you need performance most!

Grab yours at:

https://www.sharpedgesok.com/product/Lister-Star-Clipper-Green

3 Tips to ensure your blades get safely mailed-in in 20251. Individually wrap your blades in bubble wrap, or newspaper t...
02/24/2025

3 Tips to ensure your blades get safely mailed-in in 2025

1. Individually wrap your blades in bubble wrap, or newspaper to prevent the teeth from getting broken. Do the same with your shears to prevent them from getting nicks.
Remember, we want to remove as little metal as necessary to get to a fresh edge. Any nicks on the cutting surface may require sharpeners to remove more metal to get past the nicks.

2. Place them inside a sturdy and secure box that will hold them in place. (please do not ship shears in an envelope unless it’s in a shear box, mailmen don’t like getting poked by shears)
Minimize movement by adding packing material.

3.Consider mailing your sharpening out so that it arrives during the first part of the week, that offers the best chance that your order will be done in the quickest manner as it won't have to sit over the weekend. (even sharpeners need a day off…lol)

Consider using our mail-in sharpening service:

https://www.sharpedgesok.com/mail-in-sharpening-service

If you have any questions regarding sharpening, pricing, and other questions about our services, feel free to send us a message here and we’ll get back to you as soon as possible.

As always, I hope this helps… 😁

Introducing the Andis Pulse ZR II RedPacked with a powerful five-speed motor, the Pulse ZR II is a heavy-duty workhorse ...
02/21/2025

Introducing the Andis Pulse ZR II Red

Packed with a powerful five-speed motor, the Pulse ZR II is a heavy-duty workhorse that gets all your grooming needs done.Only now, it’s equipped with a size 30W ceramicEDGE wide blade, providing the perfect trifecta of speed, power and efficiency.

At 36% wider and with 16% more cutting teeth than standard blades, a wide blade covers more area quickly, allowing you to finish grooms faster. The 31-tooth ceramic cutter runs cooler and stays sharper longer, while the unique one-of-a-kind tooth pattern improves hair feed and delivers a smoother finish.

Designed for all day use, fine-tune your speed for any coat type or groom.

Comes with a blade.

Get yours here…

https://www.sharpedgesok.com/product/Andis-Pulse-ZR-II-Red-w-30-wide-blade

Easy to remember, easy to doI hope this helps… 😁
02/20/2025

Easy to remember, easy to do

I hope this helps… 😁

Happy Valentine's Day 😁
02/14/2025

Happy Valentine's Day 😁

Thank you for your vote of confidence. 💪We continuously strive to improve our services and carefully pick what products ...
02/05/2025

Thank you for your vote of confidence. 💪

We continuously strive to improve our services and carefully pick what products we sell.

Top 3 Signs your blades need to be brought to a professional🙅They start to irritate the dog’s skin It’s hard to tell wha...
02/04/2025

Top 3 Signs your blades need to be brought to a professional

🙅They start to irritate the dog’s skin

It’s hard to tell what’s wrong with your shears or clipper blades at first glance. It could be a myriad of things that are causing it to improperly cut or thug on the dog’s fur. If this happens, bring it to your sharpener for inspection as soon as you can.

🙅Your shears make a clacking sound

That usually happens when your stopper falls off of your shear. But a more concerning issue is if the tips cross each other because of the missing stopper which could potentially cause an accident both to you or the dog. If replacing the stopper doesn’t stop the clacking sounds, talk to your sharpener.

🙅Your shears fold hair

You notice your shears aren’t cutting hair. Instead, they’re folding and tugging. Potential reasons may be that it’s dull, misaligned, there are nicks on the blade’s surface, or improperly tensioned. Put a rubber band around your shears and put it aside until you get in touch with your sharpener.

These are the 3 common signs your blades need to be brought to a professional.

Share your thoughts in the comments below.

I hope this helps… 😁

3 Clipper care tips for 20251. Oil your blades after every groom - unlubricated blades tend to cause more friction betwe...
01/22/2025

3 Clipper care tips for 2025

1. Oil your blades after every groom - unlubricated blades tend to cause more friction between them resulting in your clipper’s motor to overheat. When neglected for a long time, this will wear your motor out faster than it should.

Solution? Keep your blades oiled.

2. Replace your old blade drive/lever. Ideally, Andis Blade dives should be changed every 6-8 weeks of regular use by a professional groomer. Heiniger, Oster, Wahl blade lever are usually good for 12-16 weeks of use by a professional groomer. Of course home groomers only working on their pets will go much longer between changes.

3. Call a professional for any technical issues - if you have a clipper that’s past its warranty period, unless you are a trained technician yourself, please avoid tampering with the electronics of your clipper that may result in further damages.

Let a professional guide you and show you how to troubleshoot your clipper first before bringing it to them. They have the necessary tools and experience to deal with the matter.

As always, I hope this helps… 😁

🚨 New Shear in the house 🚨Introducing our own Sharp Edges Comfort Grip 7in Thinner✨️Made with 440c Japanese High Carbon ...
01/20/2025

🚨 New Shear in the house 🚨

Introducing our own Sharp Edges Comfort Grip 7in Thinner

✨️Made with 440c Japanese High Carbon Steel for retaining it’s sharp edge and durability.

✨️Designed with a neutral grip to keep your hand in a more relaxed position..

✨️Creates the same soft finish as other luxury brands

You can order yours at:

https://www.sharpedgesok.com/product/Sharp-Edges-Comfort-Grip-7-thinner

For inquiries, please send us a DM.

We are looking to add another member to the Sharp Edges team...😁 Position: Blade technician Primary job responsibilities...
01/17/2025

We are looking to add another member to the Sharp Edges team...😁

Position: Blade technician

Primary job responsibilities include operating our new state of the art automatic blade sharpening machine , as well as disassemble, reassemble, test and clean blades. There is room to grow with our company, as well as the possibility of a full sharpening apprenticeship.

Applicants will need transportation to my house each morning, be reliable, have a strong work ethic, and a Willingness and ability to learn.

Hours are usually Tues - Fri. Half day Sat.
8ish - 5ish depending on how much driving we do.

Starting pay is $15 an hour.

Message me directly for any other questions or to apply...😁.

01/08/2025

Do you trust your sharpener?

Watch the video...😁

Happy New Year, everyone!
01/01/2025

Happy New Year, everyone!

Address

3425 N Ridgewood Drive
Del City, OK
73110

Opening Hours

Monday 9am - 6pm
Tuesday 9am - 6pm
Wednesday 9am - 6pm
Thursday 9am - 6pm
Friday 9am - 6pm
Saturday 9am - 6pm

Telephone

405-535-7153

Website

Alerts

Be the first to know and let us send you an email when Sharp Edges posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Sharp Edges:

Videos

If you've tried aligning your clipper blades before but couldn't do it right, watch this video...

Do you trust your sharpener? Watch the video...😁

We are excited to be returning to the Cattlemen's Congress at the Oklahoma State Fairgrounds this year! We be offering on-site sharpening, clipper repair & sales...😁

Wahl KM Supera - Go to Sharpedgesok.com to grab yours #fypシ゚viralシ #sharpedgesoklahoma #doggrooming #wahl

Here's how to clean your pet dryer! Watch the video below. I hope this helps... 😁

https://www.sharpedgesok.com/exclusive-access-to-black-friday-sales-page

Ever wondered how to change the hinge on your Heiniger Opal, Saphir, or Oster Volt? Here's how to change the hinge on your Heiniger Opal, Saphir, and Oster Volt clippers. Watch the full video below. I hope this helps... 😁

If you hear your clippers making a loud noise, don't panic. It may be one of these reasons. Watch the full video below to find out why your clippers make loud noises

Is there any special method to maintain your cordless clipper? Watch the video below and find out! 😁

Here's how to efficiently remove excess hair from your clipper blades! Watch the video below

Shortcuts

Share